Vehicles
73 not categorized PORSCHE 996T SEAL SETCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.99310090236EQ FVD cylinder head gasket sets contain high quality German sourced gaskets, seals and o-rings. This kit contains a complete set of gaskets to make a teardown / rebuild more convenient. Sold as a complete set. 1 necessary per car. To complete the gasket set for the whole engine also order part # 93010090104eq
$614.58
Make a selection 96410090200EQ FVD cylinder head gasket sets contain high quality German sourced gaskets, seals and o-rings. This kit contains a complete set of gaskets to make a teardown / rebuild more convenient. Sold as a complete set. 1 necessary per car. To complete the gasket set for the whole engine please order part # 93010090104eq
$387.20
Make a selection 99970108450 This small seal will stop the transmission fluid leak. easily replaced by removing the rear 13mm headed set screw in the rear tail cover. please remember that you will have to refill the transmission after removing the inner speedometer drive to replace this seal View/Change Diagram
From $1.00
Make a selection 993100902TUEQ FVD cylinder head gasket sets contain high quality German sourced gaskets, seals and o-rings. This kit contains a complete set of gaskets to make a teardown / rebuild more convenient. Sold as a complete set. 1 necessary per car. To complete the gasket set for the whole engine order please 93010090104eq too.
$614.58
Make a selection 96410090800EQ FVD cylinder head gasket sets contain high quality German sourced gaskets, seals and o-rings. This kit contains a complete set of gaskets to make a teardown / rebuild more convenient. Sold as a complete set. 1 necessary per car. To complete the gasket set for the whole engine order please 93010090104eq too.
$744.70
Make a selection ER2011000 Monoballs deliver precise, razor sharp handling. but rapid wear has made them impractical for all but the most serious racers. Not anymore! Weather seals - our proprietary-design monoball cartridges have weather seals to keep dirt out and extend product life. this is the only monoball suitable for street or extended track use. dirt and water contaminate ordinary products and accelerate wear. Performance - today’s sticky tire compounds generate corner loads that easily compress factory rubber bushings causing wandering alignment settings. Camber and toe flop around upredictably. weather-sealed monoball cartridges replace compliant factory rubber bushings with hardened-steel spherical bearings. Unlike...(choose a part on the right to read more) General Fitment914 1970-76911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69 912 1965-69
$299.95
Make a selection 91131802900 If your speedometer completely fails look at the angle drive first before suspecting the cable. easily checked by disconnecting the speedometer cable then lifting the car and putting it in gear to see if the angle drive spins, the part is easily replaced. always try to buy a new one as this is a wear part. purchase a speedo angle drive seal at the same time to stop the transmission fluid leak. it fits on the drive gear in the rear tail cover and is easily removed with the rear 13 mm headed set screw. You will have a fluid spill when this is removed so get ready! Refill with 80/90 weight oil only. View/Change Diagram
From $52.47
Make a selection AA500 Available only from Automobile Atlanta, this kit consists of parts that we use in our restoration shop without going overboard. General Fitment914 1970-76
$629.26
Make a selection FSPOR997GSKT Copper gaskets as used in formula 1 and indy car racing for ultimate leak proof sealing from the headers to cylinder heads, and from the catalytic converters to the headers. 4 pieces included in set. General Fitment911 2005-08
From $80.00
Make a selection AP996TT105 Agency power has just given Porsche 996tt owners another way to get an easy 20 bolt-on horsepower with this new big mouth plenum and throttle body kit. agency power set out to engineer and design a plenum that was functional, did not require additional tuning, and simply. Made power! the plenum is 6061 aluminum that retains the same shape as the factory t pipe. the reason to keep a standard t shape is that the engine works off of pulses. just like how Porsche designed, agency power kept this design and simply improved the restriction, the throttle body. the factory throttle body inlet size is 76mm that then jumps up to a 78mm id plastic plenum. General Fitment911 TURBO/GT2 2001-05
$850.95
Make a selection FVD33150020 This kit is complete and includes the front and rear monoball cartridges with press tools. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 4. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$715.00
Make a selection FVD34307201 Our direct replacement, OEM quality link uses rubber with a shore hardness value of 85. That is the same value as the rennsport models from Porsche. This link will offer superior performance under high cornering loads, more durability and are still forgiving for street use. Road noise not compromised with our links either. Facts: made in Germany. Crafted from high carbon steel and 7075 t6 aircraft aluminum. Weather sealed. Sold individually. Please note: we recommend buying these as a set, please purchase the left link, our part # FVD34307101
$93.50
Make a selection MS4L Our major service kit consists of everything we use when performing a thorough 914 major service. Don’t be caught short of parts when you do yours! Air filter, fuel filter, oil filter, strainer kit, alternator belt, spark plugs, points, distributor cap, distributor rotor, valve cover gasket kit, oil cap seals (1.8), distributor o-ring, condenser, oil drain plug washer. Please specify year and engine size when ordering. General Fitment914 1970-76
$196.58
Make a selection FVD3419991 This is a cost effective alternative to buying new control arms. Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with new bushings of the same rubber (65 shore hardness value). This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection FVD500964965 This kit contains everything necessary to transform your narrow body c2 or c4 into a 965 wide body / turbo look. It includes motorsport quality glass-reinforced plastic (grp) front + rear bumper and side skirts along with metal fender flares. General Fitment911 1989-94
$7,353.98
Make a selection MS4E Our major service kit consists of everything we use when performing a thorough 914 major service. Don’t be caught short of parts when you do yours! Fuel filter, oil filter, strainer kit, alternator belt, spark plugs, points, distributor cap, distributor rotor, valve cover gasket kit, oil cap seals (1.8), distributor o-ring, condenser, oil drain plug washer. Please specify year and engine size when ordering. General Fitment914 1970-76
$113.33
Make a selection NLA54295000 Aluminum holding rail set for side window seals, 1 set per car. Fits all convertibles. General Fitment356 1950-59356 1960-65
$44.00
Make a selection MIS2000 Great inexpensive way to convert your four lug wheel bolt pattern to the five lug 911 style so you can add six inch five lug wheels. General Fitment914 1970-76
$1,152.26
Make a selection 029198009 All of the gaskets and seals to completely rebuild your engine except for the front and rear main seals! this kit is specifically for the 1974-75 914 1.8 but contains only muffler gaskets for the 74 muffler. Also order four muffler gaskets if you have a 75 model with the factory heat exchangers. General Fitment914 1970-76
$95.99
Make a selection 2110900 Unique design actually grips steering knuckle for extra strength. Combined with a super strong 12mm grade 12.9 bolt, this is a sturdy solution. Height adjustable from .50" to 1.25" in 1/8" increments by positioning 3 spacers above/below steering knuckle. Articulates an impressive +/- 27 degrees to prevent binding at full compression and droop. Bump steer is a change in toe setting resulting from vertical wheel displacement. A car that bump-steers requires constant adjustment at the steering wheel to maintain a steady trajectory over uneven surfaces. This can be handful to drive. The 911/914 series has some bump steer inherent even in the stock configuration. The problem becomes more severe with lowered ride ...(choose a part on the right to read more)
$335.00
Make a selection 100124275 Ims single row pro. Single to double row retrofit bearing kit.
$999.56
Make a selection 10010303808 The 11.8:1 compression will provide you with more acceleration than kits with 11.3:1 compression. However, this kit cannot be used with original cams, it requires a more aggressive cam (maximum valve lift (tdc) of 2.1 mm) and has very deep pockets for use with rsr valves. The 109-mm size means that the housings must be modified on non rennsport models. If you have a European rennsport model, these would be slip fit. This kit also requires the larger o-ring seals, part # 96410440180 and larger base gaskets, part # FVD116929. Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resi...(choose a part on the right to read more)
$12,139.99
Make a selection 61660930300 All these are in the wire set, we have original beru plug connectors separately. These come with the rubber seal to the engine tin and with end boots to seal against the spark plug.
From $16.06
Make a selection 91135295100 Known as: mounting parts / parts kit comprising: expanding spring retaining pin safety seal / mounting parts 1 set View/Change Diagram
From $52.33
Make a selection 444552985049 This set includes a high quality radio cover, ignition cover, and glove box covers. Each piece is a polished (gloss finish) carbon overlay, meant to be adhered to your original plastic trim covers. We recommend adhering the carbon overlays to your originals with wurth bond and seal (sold separately). Great detail is taken to attempt to match the original weave size, color and polish. Whether you are adding carbon to the interior or matching existing pieces, this is high quality and is made in Germany so it is made to last, like the original. Sold as a complete set. Please note: this is for cars with air bags!
$2,655.40
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |